Browsing by Author "Weerasinghe, W.A.D.S.S."

Now showing 1 - 2 of 2

Investigation of a solid state redox capacitor based on polypyrrole electrodes
(Faculty of Science, University of Kelaniya, Sri Lanka, 2016) Weerasinghe, W.A.D.S.S.; Bandaranayake, C.M.; Vidanapathirana, K.P.; Perera, K.S.
Conducting polymers (CPs) have received a great attention as a class of potential candidates for diverse applications including batteries, electro chromic devices and redox capacitors. They surpass the carbon based materials in many applications due to their fascinating properties such as easy synthesis, low cost and good stability. In this study, it is reported about the application of a conducting polymer in a redox capacitor fabricated with a gel polymer electrolyte (GPE) of which the ionic conductivity is similar to a liquid electrolyte but having a mechanical stability like a solid electrolyte. Conducting polymer, Polypyrrole (PPy) was polymerized on to Fluorine doped tin oxide (FTO) glass galvanostatically using a three electrode set up. Sodium Dodecylsulfonate (SDS) was used as the salt. Thickness of PPy film was maintained at 1 μm. GPE was prepared using polyvinylidenefluoride (PVdF), zinc trifluoromethanesulfonate (Zn (CF3SO3)2 – ZnTF) (Aldrich), ethylene carbonate (EC) and propylene carbonate (PC). The starting materials were magnetically stirred, heated and the hot mixture was pressed in between two glass plates. Thereby, it was possible to obtain a bubble free thin film. Redox capacitor was fabricated using two PPy : DS films having an area of 1 cm2 as electrodes and a GPE having same area as the electrolyte. Configuration of the redox capacitor was in the form of PPy : DS / PVdF : EC : PC : ZnTF / PPy : DS. Electrochemical Impedance Spectroscopy (EIS) measurements of the redox capacitors were carried out within the frequencies ranging from 400 kHz to 0.01 Hz using a frequency response analyzer (Metrohm AUTOLAB 101). Cyclic Voltammetry (CV) measurements were carried out in the potential window of 2.5 V - (-2.5) V at the scan rate of 10 mV/s by means of a computer controlled potentiostat / galvanostat. For, Galvanostatic Charge Discharge (GCD) test, redox capacitor was first galvanostatically charged to 0.5V, immediately subjected to a galvanostatic discharge up to 0.0 V. The maximum charge and discharge currents were set to 1.0x10-4 A. In the electrochemical impedance plot, high-frequency intercept of the semicircle on the real axis provides the resistance of the bulk electrolyte, the diameter of the semicircle gives the value of the charge transfer resistance. At the low frequency range electrodes exhibit a nearly straight line of a limiting diffusion process which is a characteristic feature of pure capacitive behaviour. The specific capacitance was obtained from the bode plot and the value obtained was 8 F/g. The calculated specific capacitance from the CV test was 22 F/g. The difference between the capacitance values may be that the value obtained in CV method depends on the scan rate. Galvanostatic charge-discharge test showed that the specific capacitance reduction after 500 cycles was about 3%. Even though the capacitance values are little bit lower, the selected combination of PPy and PVdF based gel polymer electrolyte is seemed to be suitable for redox capacitors
Optimization and application of a gel polymer electrolyte in redox capacitors
(Faculty of Science, University of Kelaniya, Sri Lanka, 2016) Bandaranayake, C.M.; Weerasinghe, W.A.D.S.S.; Perera, K.S.; Vidanapathirana, K.P.
Energy production via renewable sources and saving it efficiently has become timely needed issues all around the globe. Supercapacitors have been identified as a class of suitable energy saving devices with respect to conventional capacitors and batteries. There are two types of supercpacitors namely redox capacitors and electrochemical double layer capacitors. In this study, redox capacitors were fabricated using a gel polymer electrolyte (GPE) and two conducting polymer electrodes. GPE was consisted with polyacrylonitrile (PAN) as the polymer, sodium thiocyanate (NaSCN) as the salt and ethylene carbonate (EC), propylene carbonate (PC) as solvents. Hot press method was used to prepare the GPE. Its composition was optimized by varying the salt concentration and measuring the room temperature conductivity. Characterization of redox capacitors was done using Electrochemical Impedance Spectroscopy (EIS) and Cyclic Voltammetry (CV). When increasing the salt concentration, the room temperature conductivity increased initially but after a certain concentration, it started to decrease. The increment of conductivity with salt concentration may be due to the increment of charge carriers which are directly responsible for conductivity. The following decrement with further increment of salt concentration may be due to lowering of charge carrier motion upon viscosity enhancement and also due to formation of ion pairs or clusters which do not assist conductivity as per their neutrality. The optimum room temperature conductivity was 1.92 x 10-3 Scm-1. The composition which exhibited the highest room temperature was selected to fabricate redox capacitors. A thin GPE film was sandwiched in between two identical polypyrrole (PPy) electrodes which were galvanostatically polymerized in the presence of sodium perchlorate (NaclO4). Impedance data were gathered using a frequency response analyser and specific capacitance was calculated using the bode plot. The specific capacitance was found to be 85 F/g. Under the CV test, cycling was done at the scan rate of 10 mV/s in the potential window -1.0 V to +1.0 V. The calculated specific capacitance was 102.7 F/g. The difference between the two values obtained by the two methods may be due to the fact that the specific capacitance value obtained using CV test is depending on the scan rate. Apart from that slight difference, the specific capacitance values are seemed to be satisfactory. The combination of the GPE based on PAN and the polymer electrodes based on PPy are suitable to be employed for redox capacitors.