Science
Permanent URI for this communityhttp://repository.kln.ac.lk/handle/123456789/1
Browse
18 results
Search Results
Item Cu2O Homojunction Solar Cells: Efficiency Enhancement with a High Short Circuit Current(2024) Thejasiri, S. A. A. B.; Jayathilaka, K. M. D. C.; Kafi, F. S. B.; Kumara, L. S. R.; Seo, O.; Yasuno, S.; Sakata, O.; Siripala, W.; Wijesundera, R. P.Cu2O homojunction solar cells were fabricated using potentiostatic electrodeposition technique. n-Cu2O thin films were grown in an acetate bath while p-Cu2O thin films were grown in a lactate bath. In the growth of n-Cu2O films, cupric acetate concentration, pH and temperature of the bath, deposition potential and duration (film thickness) and annealing temperature were investigated. In the growth of p-Cu2O on n-Cu2O, concentration of copper sulphate and lactic acid solutions, pH and temperature of the bath, deposition potential and duration were investigated. In addition, the procedure of sulfidation of p-Cu2O film surface using (NH4)2S vapor, before depositing Au front contact, was also optimized to enhance the photoactive performance. The structural, morphological and optoelectronic properties of the Cu2O films were investigated using scanning electron microscopy (SEMs), high energy X-ray diffraction (HEXRD), hard X-ray photoelectron spectroscopy (HAXPES), spectral response and current–voltage (J-V) measurements. The best Cu2O homojunction solar cell exhibited Voc = 460 mV, Jsc = 12.99 mA·cm−2, FF = 42% and η = 2.51%, under AM 1.5 illumination. Efficiency enhancement with the record high Jsc value for the Cu2O homojunction solar cell has mainly been due to the optimization of pH of the n-Cu2O deposition bath and lactic acid concentration of the p-Cu2O deposition bath.Item Optimization of growth parameters of electrodeposited tin oxide thin films for PV Applications(Faculty of Science, University of Kelaniya Sri Lanka, 2023) Kafi, F. S. B.; Gunaratne, B. H.; Jayathilaka, K. M. D. C.; Wijesundera, R. P.Tin oxide (SnO2) is a promising photoactive semiconducting material due to its optoelectronics properties. Even though, growth of SnO2 using the method of electrodeposition is advantageous, it has paved low attention among semiconductor researchers. In this study, well-adhered photoactive SnO2 thin film was successfully electrodeposited on Cu substrates. The growth parameters, such as film deposition potential, bath temperature, and duration of deposition were optimized. Electrodeposition of SnO2 layers was performed on copper substrates in a threeelectrode electrochemical cell using a solution containing 30 mM SnCl2 and 150 mM HNO3 at a deposition potential of -0.85 V vs. Ag/AgCl. The fabricated best thin film resulted JSC value of 410 �A cm-2 and VOC value of 113 mV in 0.1 M NaNO3 electrolyte. The best thin film obtained at a bath temperature of 85◦ C for a deposition time of 120 seconds. The Mott-Schottky analysis revealed that the fabricated SnO2 thin film exhibits n-type conductivity, and it has a flat band potential of -0.51 V vs. Ag/AgCl.Item Photocurrent improvement in grape dye sensitized solar cells by in cooperation of electrodeposited Cu particles in TiO2 photoanode(Faculty of Science, University of Kelaniya Sri Lanka, 2023) Shakya, M. D. P. A.; Jayathilaka, K. M. D. C.; Wanninayake, W. T. M. P. K.; Kumara, R.; Siripala, W. P.; Wijesundera, R. P.A worldwide effort is currently underway to address the world's energy crisis by finding sustainable energy alternatives. The Dye-Sensitized Solar Cell (DSSC) is a type of solar cell device that functions based on electrochemical principles and uses light sensitive dyes within its TiO2 photoelectrode layer to absorb light. The DSSC, one of the potential solutions, appears to be the most viable option for a future renewable energy source due to its sustainability and environmental friendliness. In cooperation of metal particles like Au or Ag in nano scale to the photoanode is one of the promising methods to improve the efficiencies of these DSSCs. Among these metal particles Cu has some distinct properties such as abundance, low toxicity, low cost and it undergoes Localized Surface Plasmonic Resonance (LSPR) effect like Au nanoparticles. Therefore, to improve the DSSC performances, in this study, Cu particle incorporation to the TiO2 electrode was carried out by electrochemical deposition method. Homogeneous TiO2 paste prepared by mixing appropriate amount of TiO2 powder (Titanium (IV) dioxide), ethanol, and acetic acid was deposited on a transparent Indium-doped Tin Oxide (ITO) conductive glass substrate by doctor blading method. Electrodeposition of Cu particles were potentiaostatically grown in the TiO2 electrode at -700 mV vs Ag/AgCl reference electrode using a three electrode electrochemical cell configuration with Pt as the counter electrode and 0.1 M sodium acetate and 0.01 M cupric acetate electrolyte at room temperature. Natural dye grapes have been used as sensitizer in the study. DSSCs were fabricated by sandwiching above TiO2 films with a C coated counted electrode using KI/I2 based electrolyte. The devices were characterized by analysing the UV – vis absorbance spectra and current density-voltage (J-V) curves and controlled potential coulometry measurements. The UV – vis absorbance spectrum revealed that the light absorption of DSSCs enhanced due to the incorporation Cu. The power conversion efficiency of 0.10%, photocurrent density (JSC) of 501 μA/cm2, open circuit voltage (VOC) of 0.47 V, and fill factor (FF) of 42% were achieved after the Cu incorporation in the photoanode. It is found that due to the incorporation of Cu particles, a slight voltage drop was visible, but there was a significant increase in the photocurrent density (JSC) from 308 μA/cm2 to 501 μA/cm2. The efficiency also increased from 0.07 to 0.10%. DSSC with the incorporated Cu particles showed 62% enhancement in the photocurrent compared to the DSSC without Cu particles.Item Growth and Characterization of Seed‑Assisted, EDTA‑Treated, Chemical Bath‑Deposited CdS(Journal of Electronic Materials, 2021) Kumarage, W. G. C.; Wijesundera, R. P.; Seneviratne, V. A.; Jayalath, C. P.; Gunawardhana, N.; Kaur, N.; Comini, E.; Dassanayake, B. S.A simple low-cost method to enhance the electrical properties including open-circuit voltage (VOC), flat-band potential (Vfb) and short-circuit current (ISC) in the photoelectrochemical (PEC) cell of cadmium sulfide (CdS) thin films is presented. The PEC cell properties were determined using the configuration Pt/0.1 M Na2S2O3/ CdS. Three different sets of CdS thin films were grown: (a) chemical bath-deposited CdS (CBD-CdS), (b) electrodeposited seed-assisted CBD-CdS (ED/CBD-CdS) and (c) ED/CBD-CdS deposited under the presence of ethylenediaminetetraacetic acid (EDTA) in a reaction solution of CBD (ED/(CBD+EDTA)-CdS). The FE-SEM images suggested the formation of clusters with spherical shape in the presence of a seed layer. All the samples grown with seed layers demonstrated improved ISC and VOC values in the PEC cell compared to the CBD-CdS films due to better contact between the substrate and CBD-CdS. Furthermore, the carrier concentration (ND) and Vfb were also found to improve due to the introduction of the seed layer. In the case of ED/(CBD+EDTA)-CdS, the cluster size was found to be smaller, giving rise to a larger effective surface area. The improved effective surface area, interparticle connections and adhesion of CdS to the FTO substrate resulted in superior electrical properties of ED/(CBD+EDTA)-CdS compared to ED/CBD-CdS and CBD-CdS films.Item Fabrication of inverted organic solar cells on stainless steel substrate with electrodeposited and spin coated ZnO buffer layers(Journal of Polymer Engineering, 2022) Namawardana, D. G. K. K.; Wanigasekara, R. M. G.; Wanninayake, W. T. M. A. P. K.; Jayathilaka, K. M. D. C.; Wijesundera, R. P.; Siripala, W.; Malik, M. I.Polymer based organic solar cells (OSCs) are of tremendous interest as suitable candidates for producing clean and renewable energy in recent years. In this study, inverted OSCs on stainless steel (SS) substrate with zinc oxide (ZnO) as the electron selective transport layer (ESTL), are investigated, occupying bulk heterojunction blend of regioregular poly(3-hexylthiophene) (P3HT) and phenyl- C61-butyric acid methyl ester (PCBM) as the active material and poly-(4,3-ethylene dioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) as the hole transport layer (HTL). The device structure is SS/ZnO/P3HT:PCBM/PEDOT:PSS/Au. ZnO films are prepared by spin coating and electrodeposition techniques, followed by annealing under ambient conditions. The insertion of ZnO layer between the SS substrate and active layer has improved short-circuit current ( Jsc), open-circuit voltage (Voc), fill factor (FF), and power conversion efficiency (PCE) compared to those of the reference cell without ZnO layer, achieving the highest efficiency of 0.66% for the device with spin coated ZnO from sol–gel technique. This enhancement can be attributed to the effective electron extraction and the increased crystallinity of ZnO after annealing treatments at higher temperatures as further confirmed by X-ray diffraction (XRD) and scanning electron microscope (SEM) analyses.Item A Comparative Study: Sequential and Single-Step-Electrodeposited CZTS Thin Films(Physica Status Solidi, 2022) Fernando, W. T. R. S.; Jayathilaka, K. M. D. C.; Wijesundera, R. P.; Siripala, W.CZTS (Cu2ZnSnS4) is a relatively new and promising semiconductor material suitable for photovoltaic applications due to its favorable optoelectronic properties. Of the many techniques available for growing these films, a comparative study on sequential and single-step electrodeposition methods to grow CZTS films is carried out in this investigation to explore the possibility of improving the quality of the films using the inexpensive electrodeposition technique. Mainly in both methods, potentiostatic electrodeposition technique is adopted for growing CZTS thin films. In both methods, growth conditions of the CZTS films are optimized after measuring the photoresponses in a photoelectrochemical (PEC) cell of the films that resulted at the end of each deposition step. The observed structural and optoelectronic properties of the films reveal that, in general, structurally good and photoactive CZTS films can be prepared using both methods. Moreover, photoresponse and Mott–Schottky measurements on CZTS films in a PEC reveal that CZTS films prepared using the single-step electrodeposition have better photoactive properties and improved doping densities. This important finding shows that when developing CZTS-based solar cells using the inexpensive electrodeposition technique, single-step electrodeposition is more advantageous.Item Molecular tailoring of donor and acceptor materials of organic solar cells for improvement of their optoelectronic properties(Materials Science in Semiconductor Processing, 2022) Ansari, M. A.; Hafeez, A.; Mustafa, M.; Wijesundera, R. P.; Malik, M. I.Improvement in the efficiency of organic solar cell (OSC) is one of the hot topics of the modern-day research. Despite environment friendliness and several other practical advantages, the power conversion efficiency (PCE) of OSC has not yet achieved the levels of the commercial inorganic solar cells. In this context, molecular tailoring of the donor and acceptor materials can help in alignment of the energy levels in order to improve PCE. In this study, we demonstrate the introduction of different functional groups on the most widely used donor and acceptor materials namely poly(3-hexylthiophene) (P3HT) and fullerene, respectively. P3HT was successfully converted into poly(4-bromo-3-hexylthiophene), poly(4-chloro-3-hexylthiophene), and poly(3-hexyl-4-nitrothiophene) through bromination, chlorination, and nitration reactions, respectively. Similarly, fullerene was converted into phenyl-C61-pentanoic acid methyl ester, phenyl-C61-pentanoic acid, and methyl-2-C61 propionate. The success of different modifications on P3HT and fullerene was monitored by 1H NMR spectroscopy. Finally, the optoelectronic properties after the above-mentioned modifications were evaluated by UV–Vis spectroscopy and cyclic voltammetry.Item Thin film cuprous oxide homojunction photoelectrode for water splitting(Faculty of Science, University of Kelaniya, Sri Lanka., 2021) Kafi, F. S. B.; Thejasiri, S. A. A. B.; Wijesundera, R. P.; Siripala, W.Employing cuprous oxide (Cu2O) photoelectrodes in photoelectrochemical cells to generate hydrogen by water splitting is beneficial. Conventionally, it is limited in practice because of the well-known reasons of its inherent corrosiveness and poor conversion efficiencies. In this study, we have investigated the possibility of improving the efficiency of Cu2O photoelectrode in the form of p-n homojunction together with sulphidation. Initially, the optimum pH values for the n- and p-Cu2O thin film deposition baths are determined as 6.1 and 13 for Ti/n-Cu2O/p-Cu2O in photoelectrochemical cell configuration. Then, at these pH values the duration of n- and p-Cu2O thin film deposition is optimized by forming Ti/n-Cu2O/p-Cu2O photoelectrode. In this study, we found that at 45 minutes of n-Cu2O and 50 minutes of p-Cu2O thin film deposition together with sulphidation forms relatively high efficient Ti/n-Cu2O/p-Cu2O photoelectrode resulting Solar-To- Hydrogen (STH) conversion efficiency of 0.9%. In addition, current-voltage characteristic of the best Cu2O homojunction photoelectrode exhibits more negative shift in onset of photocurrent which indicates that photocurrent generation and transportation have improved by the formation of homojunction and further been enhanced by sulphidation.Item Stability of the performance of inverted P3HT/PCBM based organic solar cells(Faculty of Science, University of Kelaniya, Sri Lanka, 2021) Weerasinghe, M. L. A.; Wanninayake, W. T. M. A. P. K.; Jayathilaka, K. M. D. C.; Wijesundera, R. P.The organic solar cell extracts and converts solar energy to electricity without environmental hazardous including global warming. Bulk heterojunction (BHJ) structure of the organic solar cells (OSCs) have higher performance than the layered structure. But the main disadvantage of the OSCs is the poor stability of the device. Therefore, this study was focused on the stability of fabricated P3HT/PCBM OSCs. A series of inverted organic solar cells were fabricated on titanium substrate using spin coated P3HT/PCBM, doctor bladed PEDOT: PSS and sputter coated Au. Device characterizations were carried out under AM 1.5 illumination during 20 days. Electrical parameters of open-circuit voltage (VOC), short circuit current density (JSC), fill factor (FF) and power conversion efficiency (PCE) were obtained during 20 days from dark and light I-V measurements. Best device produced VOC of 282 mV, JSC of 2.65 mAcm-2, FF of 0.21 and PCE of 0.15%. The PCE decreased dramatically and became almost constant value of 0.04% within 20 days. FF was constant throughout the 20 days and VOC decreased slightly within 20 days. However, JSC of the device decay from 2.65 mA/cm2 to 1.0 mA/cm2 within the considered time duration. Hence, this PCE behavior of the device is due to the loss of JSC. PCE of the organic solar cell is not higher than the silicon solar cell, but it can be improved by changing the geometry of the solar cell, annealing conditions, etc. This instability of the device upon irradiation is due to photochemical and photophysical degradation in the active layer, and the active layer/electrode interface. Further, low JSC is mainly due to the low electron mobility and low exciton diffusion length. Performance of the device can be improved carefully controlling the device fabrication parameters in the inert gas surrounding.Item Effect of annealing temperature on the wetting properties of electrodeposited Cu2O(Faculty of Science, University of Kelaniya, Sri Lanka, 2021) Shakya, M. D. P. A.; Jayathilaka, K. M. D. C.; Wijesundera, R. P.; Wanninayake, W. T. M. P. K.Surface wettability is one of the important physical parameters, which manifests the affinity of a liquid towards a solid phase. In recent years, controlling the wettability of solid surfaces has drawn significant attention due to its influence in wide range of applications. Cuprous Oxide (Cu2O) is well known as a technologically important material for various fields due to its unique advantages such as low cost, high chemical stability and remarkable electrochemical performance. This work examines the impact of the post annealing temperature on the wetting ability of Cu2O thin films. A set of Cu2O thin films was deposited on Ti substrate at a deposition potential of -200 mV vs saturated calomel electrode (SCE) in an acetate bath containing an aqueous solution of 0.1 M sodium acetate and 0.01M cupric acetate at bath temperature of 60 ºC and pH value of 6.5 for 45 min. Potentiostatic electrodeposited Cu2O films were annealed in air at 100 °C, 150 °C, 200 °C, 250 °C, 350 °C and 400 °C for 20 and 40 minute separate time intervals. The surface morphological and structural characterizations of prepared samples were studied using scanning electron microscopy (SEM) and X-ray diffraction (XRD) techniques. SEM (Zeiss evols 15) and SHIMADZU (XD-D1) X-ray diffractometer were used to study the samples. XRD spectral patterns indicated the presence of Cu2O without having any impurity phases. The water contact angles were measured using the sessile drop method in order to investigate the effect of temperature on the wettability of the Cu2O films. The contact angle of Cu2O thin film changed from 110o (non-wetting) to 10o (completely wetting) with the increase in the annealing temperature. The contact angle measurement for cuprous oxide showed a transition of cuprous oxide surface from hydrophobicity to hydrophilicity and the maximum hydrophobicity was observed at 150 ± 1 oC. Similar variation and maximum hydrophobicity of the contact angle were observed for both annealing durations (20, 40 minutes). SEM micrographs of electrodeposited Cu2O thin films indicated significant changes in the surface morphology with annealing temperature. Dimension of grains becomes smaller with increasing temperature. This suggests that higher heating temperatures lead to a decrement in the contact angle. Based on the results of the investigation, surface morphology is the primary determinant of the wettability qualities of Cu2O thin films.